Specializing in the design and manufacture of automotive motor armatures and stators.

EN

The function of an automotive armature

Release Time:

2022-08-05

   Automotive Armature It is the component that plays a core and pivotal role in the process of mutual transformation between mechanical energy and electrical energy in a motor. For a generator, it is the component that generates electromotive force, such as the stator and rotor of a DC generator and the stator of an AC generator. For a motor, it is the component that generates electromagnetic force, such as the stator and rotor of a DC motor.

  The automotive armature is the component on the motor that has coils, and the coils are in relative motion to the magnetic field. In a generator, the rotating coils under force generate induced electromotive force, thus generating electricity. For a motor, the electrical coils are subjected to Ampere's force in the magnetic field, causing them to rotate in the magnetic field.

  In most generators, the field magnet is part of the rotating element, and the armature is stationary, part of the stator. Motors and generators can be composed of a stationary armature and a rotating magnetic field or a rotating armature and a stationary magnetic field. Permanent magnets or the polarized parts of electromagnets and the moving iron parts of solenoids (especially when the latter are used as switches or relays) can also be considered armatures.

  Composition of Automotive Armature:

  Automotive armature windings are divided into two major categories: DC armature windings and AC armature windings. They are used in DC motors and AC motors respectively.

  The automotive armature consists of an armature core and armature windings. The armature windings are the circuit part of the DC motor, and are the part that converts electrical energy by generating induced electromotive force and electromagnetic torque (for generators, it is the part that converts mechanical energy into electrical energy). The armature core is part of the armature circuit and also supports the armature windings, which are embedded in the slots of the armature core.

  1. The induced armature principle of DC and AC motors is roughly the same. The current in the DC motor armature winding is also AC, and it needs to be rectified by the commutator to output DC.

  2. AC motors are divided into induction motors (asynchronous motors) and synchronous motors. Induction motors are divided into squirrel-cage rotors and wound rotors according to their stator and rotor structure. Induction motors use stator windings to form a magnetic field, and rotor windings to convert electrical energy.

  3. Synchronous motors use stator and rotor windings to form a magnetic field, and stator windings to convert electrical energy.

  The armature usually refers to the part of the motor that requires an external power supply. The armature of a DC motor is the rotor, and the armature of an AC motor is the stator.

  Role of Automotive Armature in DC Motors:

  In a DC motor, the armature is the part of the rotor with wires, which can achieve the mutual transformation of mechanical energy and electrical energy. In a DC motor, the input DC power supply and armature windings can be subjected to Ampere's force in the magnetic field, forming a driving torque to drive the load to operate, converting the input DC power supply into output mechanical energy.

  In a DC generator, driven by a prime mover, the armature windings cut the magnetic flux lines in the magnetic field, forming an induced electromotive force. According to the rectification effect of the brushes, the input mechanical energy is converted into output DC energy.


Automotive armature

01-03

2023

What are the structural hotspots of a starter armature?

The starter armature moves the entire armature through the magnetic force of the magnetic poles, causing the drive gear to mesh with the flywheel gear ring. The armature of the starter is offset from the magnetic pole by a certain distance under the action of the reset spring, and the commutator is relatively long. The starter housing is equipped with an electromagnetic switch. Its magnetizing coil is controlled by the starter switch S. The movable contact is the contact bridge. The upper end of the contact bridge is longer and the lower end is shorter, so the starter circuit can be connected in two stages. The starter has three magnetic field windings. Among them, the main magnetic field winding with fewer turns is made of flat copper bars, and the other two fine wire windings are the series auxiliary magnetic field winding and the parallel auxiliary magnetic field winding (also called the holding coil). The starter one-way clutch generally uses a friction plate clutch. The working process of the starter armature is divided into two stages. The series auxiliary excitation winding mainly works in the first stage, and in the second stage it is almost short-circuited due to being in parallel with the main excitation winding; the parallel auxiliary excitation winding works in both stages, which not only increases the magnetic force attracting the armature, but also limits the no-load speed. (1) Engagement When the starter switch S is turned on, the electromagnet generates suction to attract the contact bridge. However, because the pawl rests against the blank, the contact bridge can only close at the upper end, and the series and parallel auxiliary magnetic field winding circuits are turned on. The current circuit is:

12-21

2022

Starter armature: What is an armature?

The starter armature manufacturer states that motors play a key and crucial role in the process of achieving mutual conversion between mechanical energy and electrical energy. For generators, it is the component that generates electromotive force, such as the rotor in a DC generator and the stator in an AC generator; for motors, it is a component that generates electromagnetic force, such as the rotor in a DC motor. The starter armature manufacturer states that the armature is the relative motion of the coil relative to the magnetic field of the coil-carrying component in the motor. In a generator, an induced electromotive force is generated in a forced rotating coil to generate electricity. In a motor, the energized coil is subjected to Ampere force in the magnetic field, causing it to rotate in the magnetic field. In the mid-19th century, the term "armature" was early used for inductors, i.e., holders of magnets. Part of an alternator or related equipment can be represented by any mechanical or electrical aspect. Although these two sets of terms are clearly separated, they are often used interchangeably, or a combination of mechanical and electrical terms is included. This can cause confusion when using composite motors such as brushless alternators, or when talking to people accustomed to using different configurations of motors. The starter armature manufacturer states that in most generators, the field magnet is rotating and is part of the rotor, while the armature is stationary.

12-12

2022

Starter armature: armature knowledge points

The armature manufacturer states that the armature plays a key and crucial role in the process of converting mechanical energy and electrical energy into each other. For generators, it is the component that generates electromotive force, such as the rotor in a DC generator and the stator in an AC generator; for motors, it is a component that generates electromagnetic force, such as the rotor in a DC motor. The armature is the part of a motor that has coils, and the coils move relative to the magnetic field. In a generator, an induced electromotive force is generated in the forced rotating coil to generate electricity. In a motor, the energized coil is subjected to the Ampere force in the magnetic field, causing it to rotate in the magnetic field. The armature manufacturer states that in most generators, the field magnet is rotating and is part of the rotor, while the armature is stationary and is part of the stator. Motors and generators can be composed of a stationary armature and a rotating magnetic field or a rotating armature and a stationary magnetic field. The pole shoes and moving iron parts of permanent magnets or electromagnets and solenoids (especially when the latter are used as switches or relays) can also be called armatures. The armature manufacturer states that armatures are divided into two categories: DC armature windings and AC armature windings. They are used in DC motors and AC motors respectively. Including the armature core and the armature winding, the armature winding is the circuit part of the DC motor,

< 1...121314...24 >