Specializing in the design and manufacture of automotive motor armatures and stators.

Jinzhou Hanhua welcomes ISO14001:2015 and OHSAS18001:2007 dual-system recertification audit:

Release Time：

2022-02-22

　　From July 17 to 20, 2018, TÜV SÜD China conducted a recertification audit of Hanwha Corporation's ISO14001:2015 Environmental Management System and OHSAS18001:2007 Occupational Health and Safety Management System. The four-day audit involved two auditors who, based on audit requirements, comprehensively and meticulously reviewed the planning and management of Hanwha Corporation's environmental and safety management systems, the organization's environment, risks and opportunities, assessment of environmental factors/hazards, compliance with laws, regulations and other requirements, targets and indicators, and environmental and occupational health monitoring, etc., for the past year. The auditors affirmed Hanwha Corporation's environmental and health and safety management system operations, while also suggesting areas for improvement and providing valuable management recommendations. Hanwha Corporation is actively addressing these improvement items and will continue to improve in future work. The recertification audit was successfully completed.

02-09

2023

Introduction to the role of the stator and rotor in a brushless motor - collect this information!

The stator and rotor of a brushless motor consist of permanent magnets with a certain number of magnetic poles embedded in or on the surface of the iron core. Most permanent magnets are made of rare-earth permanent magnet materials with high coercivity, such as neodymium, iron, and boron, and high magnetic permeability and magnetic induction density. The rotor magnets are similar to those in brushed motors; both produce a sufficient magnetic field in the air gap of the motor. The difference is that the permanent magnets in brushed motors are mounted on the rotor, while those in brushless DC motors are mounted on the stator. The rotor system structure of brushless DC motors often adopts different surface-mounted magnets, also known as tile magnets, with radially magnetized tile-type permanent magnets bonded to the outer surface of the iron core. Through reasonable design, a square-wave air gap magnetic flux density can be obtained. What is the injection molding process for the stator and rotor of a brushless motor? Metal inserts are placed in the mold, and then BMC plastic is injected and heated to 160 degrees. The power of the motor should be selected according to the power required by the equipment, so that the motor operates under rated load as much as possible. Two points should be noted when selecting: (1) If the motor power is too small, a "small horse pulling a large cart" phenomenon will occur, causing the motor to be overloaded for a long time and damaging it.

01-30

2023

What are the components of a starter motor armature?

The control device of the starter armature includes an electromagnetic switch, a starter relay, and an ignition start switch, etc., among which the electromagnetic switch is made together with the starter armature. I. Electromagnetic switch 1. Structural characteristics of electromagnetic switch The electromagnetic switch is mainly composed of an electromagnetic iron mechanism and a motor switch. The electromagnetic iron mechanism is composed of a fixed iron core, a moving iron core, an attracting coil, and a holding coil. The fixed iron core is fixed, and the movable iron core can move axially in the copper sleeve. The front end of the movable iron core is fixed with a push rod, and the front end of the push rod is provided with a switch contact plate. The rear end of the movable iron core is connected to the fork through an adjusting screw and a connecting pin. The reset spring is arranged outside the copper sleeve to reset the movable parts, such as the movable iron core. 2. Working principle of electromagnetic switch When the directions of the magnetic fluxes generated by energizing the attracting coil and the coil are the same, their electromagnetic attractions overlap each other, and the moving iron core can be attracted to move forward. The pad at the front end of the push rod until the electrical switch contacts are connected to the motor main circuit. When the magnetic pain caused by the energization of the attracting coil and the coil is in the opposite direction, their electromagnetic attractions cancel each other out. Under the action of the reset spring, the movable iron core and other movable parts automatically reset, the pads and contacts are disconnected, and the motor main circuit is disconnected. II. Starting relay

01-10

2023

What is the manufacturing method for the starter armature structure?

The starter armature structure can increase the energization time of the starter and avoid the problem of short circuit caused by the ablation of the copper wire winding after the armature is energized for a long time, thus ensuring the safety of the circuit. The starter armature structure includes an armature shaft, an armature winding, an iron core and a commutator. The armature winding includes an end winding i arranged away from the commutator. The end winding i is provided with a U-shaped portion, and the U-shaped portion is provided with an insulating sleeve. The melting point of the insulating sleeve is higher than 200 ℃. The iron core is fitted on the armature shaft, and the iron core is provided with a winding slot i, and the armature winding is embedded in the winding slot i. An insulating piece i is set in the winding slot i to isolate the armature winding from the iron core and the edges of the components of the armature winding. The insulating piece i has an S-shape structure to wrap the edges of the components of the armature winding. The commutator is fitted on the armature shaft and is arranged near the end of the armature shaft. The commutator is provided with a winding slot ii. The armature winding also includes an end winding ii, which is arranged near the commutator and embedded in the winding slot ii. The end winding ii is composed of an inner ring layer and an outer ring layer, and an insulating element ii is arranged between the inner ring layer and the outer ring layer to isolate the inner ring layer and the outer ring layer. The clamping ring is also fitted at a position corresponding to the winding slot ii on the commutator. The insulating sleeve is made of glass fiber. Compared with the existing technology, this invention

< 1...11 12 13...24 >

Add：NO 2, Section 4. Bohail Avenue,Jinzhou Economic and Tchnical Development Zone, Jinzhou

Sales Department：+86 416-2933839

Http：www.jzhhdz.com

Email：hhdz_sales@163.com

Scan To Learn More

COOKIES

Our website uses cookies and similar technologies to personalize the advertising shown to you and to help you get the best experience on our website. For more information, see our Privacy & Cookie Policy

COOKIES

required

These cookies are necessary for basic functions such as payment. Standard cookies cannot be turned off and do not store any of your information.

analyze

These cookies collect information, such as how many people are using our site or which pages are popular, to help us improve the customer experience. Turning these cookies off will mean we can't collect information to improve your experience.

Feature

These cookies enable the website to provide enhanced functionality and personalization. They may be set by us or by third-party providers whose services we have added to our pages. If you do not allow these cookies, some or all of these services may not function properly.

advertise

These cookies help us understand what you are interested in so that we can show you relevant advertising on other websites. Turning these cookies off will mean we are unable to show you any personalized advertising.

Copyrights Jinzhou Hanhua Electrical Systems co., ltd. Website：300.cn jinzhou.300.cn SEO Privacy Policy

Business License