Specializing in the design and manufacture of automotive motor armatures and stators.

Jinzhou Hanhua Company's trade union organized autumn tug-of-war and basketball competitions

Release Time：

2022-02-22

　　Jinzhou Hanhua Company's Labor Union organized a tug-of-war and basketball competition in autumn: Welcoming the Mid-Autumn Festival and National Day, from September 23rd to 24th, Hanhua Company's Labor Union organized an autumn tug-of-war competition for employees in their spare time. This tug-of-war competition was divided into men's, women's, and mixed groups, with a total of 10 teams participating. The competition adopted a round-robin format, with a best-of-three system. After fierce competition, the No. 1 Workshop Warriors team finally won the championship. From September 27th to 29th, the Hanhua Labor Union held an autumn basketball competition, and finally the No. 2 Workshop team won the championship trophy. The spirited and passionate players won warm applause from everyone present. The two competitions held by the labor union enhanced the team cooperation awareness of the company's employees, demonstrated the harmonious and optimistic spirit of Hanhua employees, enriched the employees' spare time, enlivened the atmosphere among employees, and powerfully proved that "Unity is strength" and "We workers have strength".

Jinzhou Hanhua

09-13

2022

Methods for winding the armature of a DC brushless automotive motor

The method for winding the armature winding of a DC brushless car motor is to leave a section of the cable end free and tie it tightly to the shaft. Hold the car armature with one hand, and wind the coil inductance clockwise with the other hand. Taking a five-slot armature as an example, the first coil is 1-5, the second coil is 2-6, then 3-7..., and so on. The sides of many components are on the next layer. The 5-9 components have one side on the next layer and the other side on the top layer. The sides of many components are on the top layer. In order to ensure the insulation between the top layer and the next layer components, it is advisable to place 0.1-0.15mm thick insulating paper pads in between. When the coil inductance in the slot reaches a certain level, a crossbar is needed to make it reach the bottom of the slot. When winding the coil inductance, the wire should be tightened first. Whether in the slot or the wire connection part, it is necessary to prevent the occurrence of crossed turns to prevent excessive space occupation and short circuit between turns due to partial stress of the wire. After all the windings are wound, the wire ends of the same winding component are bundled together, then the insulation layer of the wire connector is removed, different color waterproof sleeves are used, and they are embedded in the corresponding commutator segments. The important role of the armature in a DC brushless motor: DC motor,

09-05

2022

The function of a DC motor armature

The armature is a crucial component in an electric motor, playing a central role in the conversion between mechanical and electromagnetic energy. In a generator, it is the component that generates the electromotive force, such as the rotor in a DC motor and the stator in a DC motor. In a motor, it is the component that produces the magnetic force, such as the rotor in a DC motor. The armature is the component in an electric motor that contains the coils, which move relative to the electromagnetic field. In a generator, the rotation of the coils generates an induced current, producing electricity. In a motor, the energized coils are subjected to Ampere's force in the magnetic field, causing rotation. A DC motor or related equipment can be described from either a mechanical or electrical perspective. Although distinctly separate, these two terminologies are often used interchangeably or in combination. This can lead to confusion when using hybrid devices such as brushless DC motors or when communicating between personnel accustomed to different equipment configurations. In most generators, the field magnet rotates and is part of the rotor, while the armature is stationary and part of the stator.

08-22

2022

Design rules for automotive armatures

Automotive armature manufacturers indicate that single-layer windings are not suitable for large-capacity motors, and small-capacity motors should not be double-layered. The magnetic flux density of the motor core should not be too high or too low. When the frequency and thickness of the silicon steel sheet core material are constant, the iron loss depends on the magnetic flux density. If the magnetic flux density is too high, the iron loss increases, and the motor efficiency decreases. The increased heat from the iron core increases the motor temperature, and the increased excitation power increases the motor power factor, so the magnetic flux density of the core should not be too high. Try to avoid excessive saturation of the magnetization curve. If the magnetic density is too low, it will increase the amount of motor material used, increasing the cost. The rotor teeth are narrow, the magnetic density is high, the slot entry wire is large, that is, the automotive armature slots are large. Automotive armature manufacturers indicate that due to poor air conduction, there are many gaps in the slots, affecting the coils and easily damaging the heat dissipation of the insulation material, accelerating the increase in motor temperature. The slot fill factor of the motor slots cannot be too high or too low. Usually, the slot fill factor for low-speed motors is 75% to 85%, which can effectively prevent the enamelled wire from loosening in the slots. The design of the motor rotor slot shape should use parallel trapezoidal recesses as much as possible, and the edges of the recesses should not have sharp corners. Try to use a circular bottom recess, because the circular slot is filled with aluminum, which is easy to injection mold and the stator chip is easy to insert. The coil current density should not be...

< 1...16 17 18...24 >

Add：NO 2, Section 4. Bohail Avenue,Jinzhou Economic and Tchnical Development Zone, Jinzhou

Sales Department：+86 416-2933839

Http：www.jzhhdz.com

Email：hhdz_sales@163.com

Scan To Learn More

COOKIES

Our website uses cookies and similar technologies to personalize the advertising shown to you and to help you get the best experience on our website. For more information, see our Privacy & Cookie Policy

COOKIES

required

These cookies are necessary for basic functions such as payment. Standard cookies cannot be turned off and do not store any of your information.

analyze

These cookies collect information, such as how many people are using our site or which pages are popular, to help us improve the customer experience. Turning these cookies off will mean we can't collect information to improve your experience.

Feature

These cookies enable the website to provide enhanced functionality and personalization. They may be set by us or by third-party providers whose services we have added to our pages. If you do not allow these cookies, some or all of these services may not function properly.

advertise

These cookies help us understand what you are interested in so that we can show you relevant advertising on other websites. Turning these cookies off will mean we are unable to show you any personalized advertising.

Copyrights Jinzhou Hanhua Electrical Systems co., ltd. Website：300.cn jinzhou.300.cn SEO Privacy Policy

Business License